Craig

I was brave and glued the back on the model.
This was kind of scary, since I don’t get to touch the wiring ever again and hopefully it’s solid.

I sculpted a icicle on his arm where a particularly nasty white section was from where the sprue attached, and a few more icicles on his butt where I drilled into it to get the wires through. I painted these with a Vallejo white primer that I picked up a few days ago, as opposed to the Imperial Primer that I used for the Nothing Beast.

Got the LED wired up inside the golems torso today!

This was also the hardest part of this project.

Holy hell, there have been a lot of hardest parts.

The problem here is that I’m trying to do really small detail work inside of a narrow area. I have both needlenose pliers and good tweezers and I used both, switching tools whenever I needed something strong or something agile, because you can’t have both! At one point I feared that I wasn’t going to be able to do it. I ended up pulling the LED out and using the tweezers to pull loops into the inside wires. Then I turned those loops so they were face up, and dropped the LED into the two loops. Then, I carefully tightened the loops around the LED leads.

Once I got the LED wired up, I tested it again.

Then I soldered it in. Also the hardest part. Here the challenge is to get the solder onto the wires with a hot iron, without letting the hot iron touch anything plastic. Inside of a plastic box. A narrow, plastic box.

After I got it soldered, I worried that the metal bits were to close together. I’m about to glue this thing inside, and I never get to touch it again. If the wires ever touch, I’ve created a short and I don’t get light anymore. So I went back and adjusted the solder and pulled the leads further apart and…

Now I have a light inside of a torso. 🙂 From here, it gets real simple – glue the rest of the golem together.

And don’t fuck up the paint job. >.< I have to sculpt icicles to cover the holes I made while drilling for wires, and paint those icicles. A fellow on A Wyrd Place used washes to provide contrast in the recesses of the transparent model and I think I might do that. Then I’m going to use the Secret Weapon snow mix on parts that might have snow.

Still a long way to go!

Time for glue! I first glued the feet onto the base, because their positioning was the most important. Then I dry-fit the electronics six or seven times to make sure it all worked, checked the connections again (placing the LED against the wires). I glued the top piece of cork to the two pieces of cork on the front and back, as well as the top and bottom of the switch to the top cork and the base. These were the second most important parts. Not as much holding and stability as I’d like, but it’ll improve as we go.

I let that sit for a few minutes, then started filling. I pulled apart small pieces of cork and glued them into place where ever I could see into the insides. When this is all dry in the morning I’ll use oxid paste to fill all of the remaining gaps, but it works best if you don’t have to fill more than a few millimeters of hole.

Here’s a photo of where the LED will end up inside the torso. I’ve left the wires long for now, but will obviously be cutting them down to fit the light in.

Here’s what the underside looks like. You can see the switch on the right.

When I’m completely done, I’m going to fill some of the bottom with white glue to keep the battery holders in place, but for now they are snug-fit against all of the cork on top.

And here’s the next morning, with all those gaps filled.

I had some legs to run wires through. It turns out that 90 degree angles suck, and that I haven’t used my hands to really and truly pin something for years. My fingers hurt to type. >.<

In the end, I said fuck-it to the 90 degree angles – despite drilling connecting tubes, the wire wouldn’t bend and flow that way no matter how shallow I made the angle, and there’s only so much space to try to shallow it out more. Instead I drilled out in straight lines with the bends outside of the model, and then ran the wire through the tubes. Once it was in both sides, I pulled on the wire to bring it as close to the model as possible. I’ll sculpt something over it, it’s fine.

I think this is one of the harder parts of this whole project.